extruder equipment-manufacture,factory,supplier from China

When using a twin-screw extruder, the twin-screw extruder needs to install the device correctly, so that it can save energy and time during production.The twin-screw extruder is fully automated from batching, extrusion, puffing, molding, core sandwiching, cutting, spraying to finished products at one time. The production line has the characteristics of many optional models, flexible equipment configuration, wide range of raw materials, many types of products, and simple operation.

For extruder equipment, the model specifications of extruder equipment are classified according to the diameter of the screw. For the sake of explanation, plastic is used as an example below, but the same is true for food extruders.That is to say, the screw diameter of the extruder equipment is the model specification of the extruder equipment. For example, the screw diameter of the 90-type extruder equipment is 90mm.

With the needs of daily life, extruders are widely used, and can be divided into four areas: drainage area, feeding area, screw conveying area and discharging area.1. The equipment adopts a shaftless screw, and the contact area with the material is small, that is, the friction force is small, which can effectively improve the extrusion efficiency of the extruder, and can avoid problems such as clogging and winding.2. The equipment is made of stainless steel, which has high strength and strong corrosion resistance, so it has a long service life.3.

As October approaches, konjac also ushered in the harvest season. The suitable planting areas of konjac in my country are mainly distributed in the tropical and subtropical humid monsoon climate regions such as the Southeast Mountains, the Yunnan-Guizhou Plateau, and the mountains around the Sichuan Basin.Konjac has been cultivated and eaten in my country for a long time. The processed products of konjac are not limited to the konjac tofu that people often eat in the past. Konjac has been processed into various snacks and snacks, which are deeply loved by consumers.

Twin screw extruder is developed on the basis of single screw extruder. Two screws are placed side by side in the barrel of the twin screw extruder. According to the meshing degree of the two screws can be divided into mutual meshing type and non-meshing type. According to the rotation direction of the two screw shafts, it can be divided into reverse rotation type and co-rotation type.(1) meshing twin screw: Because the meshing gap of the meshing screw is very small, the material has the ability of forced conveying, not easy to produce backflow, leakage phenomenon.

Series double screw extruder introduction:1, mainly by the feeding system, extrusion system, rotary cutting system, heating system, lubrication system, control system.2, extruder feeding system, main drive system, rotary cutting system all adopt frequency control, strong power, smooth operation, power saving.3, automatic lubrication, forced cooling, to ensure the safe operation of the extruder and prolong the life.4, screw alloy material, through special processing, high strength, wear resistance, increase the service life.5, according to different products, with different structure and length

When operating a twin-screw extruder, it should be maintained on time. The maintenance process is carried out after the twin-screw extruder runs continuously for 2500-5000h and shuts down. The screw is extracted to inspect, measure and identify the wear condition of the most critical components, replace the components that have reached the specified wear limit as soon as possible, and repair the damaged components . The maintenance standard of the reducer of the twin-screw extruder is the same as that of the ordinary standard reducer.

Twin screw extruder to keep clean can produce better products, keep clean can also reduce the occurrence of failure rate, ensure the continuous production, twin screw extrusion equipment maintenance basic elements - inspection, cleaning.The inner wall of cooling water pipe attached to twin screw extrusion equipment is easy to scale, and the outside is easy to rust and corrosion. The maintenance should be carefully checked.

The screw extruder was first used in the plastics industry, and its theoretical research started earlier, forming a variety of mathematical models used to describe the basic principles of flow and heat transfer in the extrusion process, using these models to achieve accurate extrusion machine simulation Design. The application of extrusion technology in the food industry is slightly later than that in the plastics industry, which is mainly due to the complexity of food raw materials.

Directly puffed food is generally required to be dried after extrusion processing. The moisture content of the dough in the extruder is 15%~20%. The product is then dried to reduce the moisture content to 2% to 3% to create the environment needed for a crunchy texture and stable shelf life. Due to the low density of the product, the drying time is usually very short, so it should be carried out in a warm warehouse.Coatings to produce direct-expanded products Extruded and dried products are finally sprayed with oils and seasonings.